själv använder jag bara det bästa
- filmretreiver extraordinär.jpg (21.09 KiB) Visad 6075 gånger
inget jag har provat men i brist på kapsylöppnare så har jag provat sådana här:
men det har alltid slutat så här då
alltid positivt med tummen upp
- filmretriever tummen upp.jpg (21.86 KiB) Visad 6075 gånger
ja, nog om skoj o skämt nu
intresset började när jag såg denna lilla tingest som är till för att dra ut filmen ur polaroids 35mm film.
- polaroid film retriever.jpg (63.73 KiB) Visad 6075 gånger
mycket riktigt fanns det några som hade knåpat själva. här är två jag hittade:
DIY Film Puller by fullframe, on Flickr
och en till:The arrow is pointing in the direction you're going to insert this into the canister. The hooks were cut into the sprockets to catch the sprockets of the film leader. This is just an illustration, you should cut more notches.
Once you have enough of this film puller in the canister turn the spindle counterclockwise (if you're looking at the canister with the spindle pointing towards you) until you feel the hooks catch. Slowly pull the film puller out. If things work it should drag out the film leader. You may have to try more than once.
Kod: Markera allt
_____________________________________________________________________________
| __ __ __ __ __ __ __ __ __ __ __
| | | | | | | | | | | | | | | | | | | | | | |
| |__| |_ | |__| |__| |__| |__| |__| |__| |__| |__| |__|
|
|
|
|
| this is a piece of regular scrap film!
|
|
|
|
| __ __ __ __ __ __ __ __ __ __ __
| | | | | | | | | | | | | | | | | | | | | | |
| |__| |_ | |__| |__| |__| |__| |__| |__| |__| |__| |__|
|_____________________________________________________________________________
this is what you make out of the film above!
_____________________________________________________________________________
/ __ __ __ __ __ __ __ __ __ __ __
| | \. | | | \. | | | \. | | | \. | | | \. | | | |
| |_____\|__| |_____\|__| |_____\|__| |_____\|__| |_____\|__| |__|
|
| ^
| |
| bend "barbs" _down_ towards emulsion side
| insert notice then they will slide into casette
| <--- this end into casette easily but on way back will catch sprocket
| first holes
| |
| V
| _________ _________ _________ _________ ______ __ __
| | ./| | | ./| | | ./| | | ./| | | ./| | | |
| |__ / |_ | |__ / |__| |__ / |__| |__ / |__| |__ / |__| |__|
\_____________________________________________________________________________källa: http://people.rit.edu/andpph/text-retriever.htmlYou can usually just use one piece of this sharksin film and stick it as much as will go into the casette. Then wind the core until you feel resistance. Then pull it out and the film may come out with it.
Or, use two pieces of film, one plain with no sharskin pattern cut into it and the other which is modified as shown above. Insert a length of plain film as far as it will go into the casette ( usually it will only make one turn inside the casette and get stopped by the felt. Then insert the modified film "under" the plain one and proceed as above. The function of the _plain_ piece is to smooth out the inside of the casette so the leader will not have a chance to get caught on the felt light trap's edge.
